80/105 LandCruiser - Flipped Radius Arm Kit
Pay in 4 interest-free instalments with Afterpay · Zip available
Got a Cruiser and looking at setting up the front end? Flipped radius arms are a great compromise to obtain the correct amount of castor to suit your lift, grab a bit more clearance under the diff and get a nicer, flatter arm!
This kit has been developed to use the factory radius arms, which eliminates the need for purchasing new arms, as you simply install the new brackets to suit the desired castor. Whilst you're welding to your housing, you'd be silly not to chuck a brace kit over it as well to help give some peace of mind when belting it against that surprise rock! So the kit can also come with exactly that!
For those wanting the radius arm mounts and/or just the panhard mount, they are available for purchase as well.
Factory castor figures are 2.5-3 degrees. We suggest and aim for 4 degrees after the conversion.
If you're not confident to fit it, we've built a jig to get it bang on first go and every time!
Housings are stripped of the factory radius arm brackets, then fully blasted for ease of welding (and easier coating later), placed in the jig, new brackets installed, then swapped into our welding jig to be welded out. Checked for straightness before and after. If slightly out after welding, it's straightened on our time. If the housing is a bit out before install we can sort the problem, but this will incur additional costs as it's obviously extra time.
Exchange housings are hopefully coming soon!
When ordering this product:
Please note!
- When ordering this product, you MUST measure the trim height of your vehicle and leave it in the comments when ordering. We DO NOT want to read 3" lift. Trim height ONLY! We're not trying to be annoying, we're trying to avoid the case of you actually having a different lift height to what you think!
What's a trim height? On flat level ground at ride height, measure the distance from the centre of your hub straight up to the bottom edge of your factory guard. This will tell us exactly how much lift your car has. Please do this, as it's the only way to properly measure lift heights. So far, more lift heights have turned out taller than owners thought, and we just want to make sure you get the best result!
- If ordering Supply and Fit, we obviously need a housing to weld it all to! But we also wanted to let you all know the price of it as well. Full payment up front for fitment is not required, but welcomed if desired. Please reach out for current lead times if needed. ALL housings must come fully cleaned. A small amount of residual oil in the housing is perfectly fine, but the outside and the knuckles must be properly and fully degreased and stripped of any gunk and grease before being dropped off or sent to us. Failure to do this will incur a $300 cleaning fee.
- If purchasing Radius Arm Mounts Only, please note the cut out shape to go over the housing is only a guide. The best way to obtain the desired castor figures is to set up the chassis and diff at ride height (use the brackets as a guide to align the housing), rotate the diff to the desired castor, then tack the mounts in position.
Kit includes:
- New radius arm mounts shaped to be as close as possible to suit the position of the castor for the desired lift. (For those doing the job at home, you may still need to give the mounts a very slight grind as not all housings are the same.)
- Our top diff truss. (Left at full width to allow you to trim it to suit your needs)
- A new panhard mount for the diff to give working clearance off the new radius arm position and help align the panhard with the drag link. The bracket comes fully welded, ready to go.
- Front diff guard.
- Knuckle gussets.
- Lower shock gussets.
Some benefits of flipped arms:
- A cost effective way to obtain correct castor figures for your lift and brace your housing at the same time!
- More clearance under the diff housing while playing off-road.
- A flatter arm in suspension is a happier arm! This means you'll see less longitudinal movement or flex steer, as well as a freer moving arm. The best analogy for this: grab a broom handle and point it at the ground at say 30deg, then push the handle into a crack. You'll notice the handle will push back on your hand and not be as inclined to go over said crack. Do it again but with the handle at 10deg and you'll find the handle will have drastically reduced force going up it and will be a lot happier to essentially bounce over the crack. This is a very similar concept to what happens with the front diff when traversing an obstacle.
- Castor bushes are not needed (nor should they be used), so there's no loss of potential wheel travel.
- The change of mounting angle on the arm will also bring in some additional anti-dive properties. This will help reduce the front end diving hard under brakes. It will also help a little bit off-road while climbing.
- The new radius arm location forces the need to relocate the panhard mount, as the factory location will not clear the arm. This is actually a blessing in disguise, as the new mounting location in our kit not only gives the clearance needed, but also helps align the panhard and drag link a lot better! This will drastically reduce the small amount of bump steer in the car, as well as slightly raising the roll centre to aid stability.
Disadvantages: (We won't tell you fibs!)
- With the flip come clearance issues. Thanks to the arm shape and new location, 30-40mm bump extensions are required to keep the arm off the chassis rail on full bump.
- If you have them, the smaller bump stops under the chassis rail cannot be run.
- There is no loss, but there is also no gain in flex (not that we see that as a problem, as flex does not dictate how capable a vehicle is). If by chance you are coming from castor bushes, then this point is actually not relevant, as you'll see the potential for more travel.
- The factory sway bar is physically not going to fit back in the car with the arms on the top of the housing. There is just not enough room to allow it to work.
- Due to the variations between vehicles, we cannot confirm that your current panhard (stock or aftermarket) will clear accordingly. Consideration needs to be taken in this matter.
- Unfortunately our alloy panhard won't work with this setup, as it requires a small bend to clear the new arms. We are working on a steel replacement for those interested.
Not sure if this product is right for you? Please email the Rampt team at info@ramptcustoms.com.au to enquire.
Pick up free from our Cardiff workshop, or choose delivery at checkout. Courier rates are worked out by weight and state. Kits, large items and orders over 50 kg are quoted once your order is packed, and ship once freight is paid. Smaller parts go by courier: QLD, NSW, VIC, SA & TAS 2–4 days, WA & NT 5–10 days. Large kits go by pallet to your nearest depot. Physical addresses only.
Change-of-mind returns within 30 days of shipping or collection, subject to a 20% fee. Made-to-order and custom parts excluded. Your rights under Australian Consumer Law are unaffected.
We ship worldwide. Email your address, phone number and parts list and we'll come back with a freight quote.
Complete the setup

Sale
Sale
Sale