80/105 LandCruiser - Rear Top-Mounted Axle Truss

80/105 LandCruiser - Rear Top-Mounted Axle Truss

$230

Pay in 4 interest-free instalments with Afterpay · Zip available

Finish FLAT PACK
Options TRUSS ONLY
AvailabilityIn-stock orders dispatch in 1–3 business days, usually within 24 hours. Not on the shelf? Allow 1–3 weeks.
Not sure what you need?Call 0421 382 071 — tell us your vehicle, lift and how you use it.

Are you building a 4-Link for your LandCruiser, or converting to LandCruiser diffs in your build?

Our Rear Top-Mounted Axle Truss Kit is designed to be a universal solution to suit most applications, if not all, helping those building at home get the work done easily and properly!


BASE KIT:

-Rear Top-Mounted Axle Truss (welded or flat pack)


The 6mm main plate sits on the axle tubes of the housing, with the two 4mm infill plates sitting on the inner edge of the main plate. This essentially self-aligns on the housing, making it almost impossible to get wrong! Infill plates are different front to rear, with corresponding keyways for maximum ease of install.


The truss sits approximately 135mm above the top of the axle tubes (30mm above the tallest part of the housing) & is 480mm wide, with the main flat or top section being 100mm x 285mm, giving ample room to land upper link tabs.


OPTIONAL COMPONENTS:

Upper Link Tabs:

-LandCruiser bush width and hole size with gussets

-3/4" heim width and hole size with gussets

-7/8" heim width and hole size with gussets


These tabs are 85mm tall from the base to the centre of the hole, and 100mm wide at the base. This gives ample tab material to get the upper links at an appropriate height and angle. If required, simply trim them and the gussets down to suit your needs. Please note: All upper link tabs are provided flat pack whether the truss is welded or not. The upper link tabs cannot be welded in-house due to variations in vehicle setups and specifications.


Custom hole sizes and widths are available for upper link tabs and gussets outside of these options. Please contact us if you require custom.


GR250 4mm & 6mm Mild Steel CNC Cut & Folded In-House.


PLASMA CUT PARTS

Plasma cutting will leave a thin layer of nitride on the cut edge of the plate. To assist with obtaining the best possible weld on construction, this layer of nitride needs to be cleaned or ground off. If not cleaned up it can be similar to welding over thin paint. All welded options ordered are cleaned in house before welding, and we suggest doing the same with flat pack orders.


INSTALLATION

We have designed this kit to be as user friendly as possible, so much so that there are only two important factors to get right.


1: Pay close attention to the cut outs on the bent section. One is round, the other is not so round! Place the round cut out on the driver's side of the axle tube. Use one of the infill plates to determine the central position of the truss on the axle (left/right position). Next, using a straight edge of any sort, align the front side of the main plate with the machined surface that the third member bolts to (use the last photo in this listing for reference). Once the truss is aligned, simply tack weld both infill plates to the main plate. A sneaky tack on the main plate to the housing to help keep it in position doesn't hurt. Remove from the housing and weld the truss together on the bench. Once cool, place it back on the housing and tack into position ready for welding.


2: Welding a truss or any bracket of decent size to a diff housing is going to create large amounts of heat. As the heat-affected area cools, it unevenly pulls the material on either side into it, thus warping the housing. The easiest way to counter this is by securing the housing in a jig, applying sufficient opposing preload and then continuing to weld out the components. Preload can be applied using a small bottle jack or similar method. Do you need a jig? Check out our 'Diff/Axle Welding Jig' listing - not only do we offer jigs for LandCruiser diffs, but Patrol too.


*PLEASE NOTE*

Not all housings are identical. Some small modifications may be required for that perfect fit up.



SUSPENSION GEOMETRY:

Suspension geometry can be a majorly overlooked factor when it comes to link or coil conversions on vehicles. Getting appropriate geometry figures for your build is just as important as, if not more important than, choosing appropriate tyres for your build. We strive to make sure that all builds everywhere are being constructed to the best they can be, to make sure the best possible outcome and driving characteristics are achieved!


This kit is NOT vehicle specific. It is designed to be a DIY kit.


If you require assistance with your build, simply hit us up for advice! We are happy to help.


Not sure if this product is right for you? Please email the Rampt team at info@ramptcustoms.com.au to enquire.

Complete the setup