80/105 Series Complete Rear End Kit —Alloy Long Arm, Panhard Riser & Links

80/105 LandCruiser - Complete Rear End Kit – Alloy Long Arm, Panhard Riser & Links

$5,130 $5,700 Sale

Pay in 4 interest-free instalments with Afterpay · Zip available

Heim Type DFI 3PC
AvailabilityIn-stock orders dispatch in 1–3 business days, usually within 24 hours. Not on the shelf? Allow 1–3 weeks.
Not sure what you need?Call 0421 382 071 — tell us your vehicle, lift and how you use it.

Lift an 80 or 105 and the rear end starts working against you. The panhard steepens, the short lower links swing the axle through a tighter arc, and the factory rubber limits flex. The result is a car that leans hard, unloads mid-corner and steers itself off the line.


This kit fixes all of it in one go.


What it does

A lifted 80 or 105 has three problems at the rear. Short lower links that swing the axle through a tight arc, causing significant roll steer. Rubber bushes that limit flex, and a panhard running at an angle it was never designed for.


Long arms. The longer lower links flatten the arm arc, so the axle tracks closer to vertical through its travel instead of swinging fore and aft. Pinion angle stays more consistent, bind falls away, and the axle stops fighting the chassis at full stuff and full droop. New lower chassis mounts and dropped upper link brackets set the link separation correctly for the longer arms, which is what controls axle wrap and torque reaction under throttle.


Panhard riser and extended bar. This is the piece that changes how the car feels on the road. At lifted ride height the factory panhard runs steeply angled, and an angled bar puts the rear roll centre in the wrong place, moves it around through travel, and behaves differently rolling left than it does rolling right. It also generates a vertical force component under cornering load that jacks the rear of the body and unloads the axle mid-corner. That is the vague, skating feeling a lifted cruiser gives you.

The riser bracket and extended bar bring the panhard back toward level. The roll centre is reset and centred, and it stays put through travel instead of migrating. Roll becomes progressive and symmetric rather than sudden and one-sided. The jacking stops, so the rear stays loaded through a corner and keeps finding traction. Lateral axle shift drops away with it, which is what kills the roll steer and stops the tyres walking across into the guards.


Solid alloy upper links. Bush and heim combination removes the deflection you get from tired factory rubber while retaining enough compliance to keep road manners sensible. The axle locates where it is meant to, under load, consistently.


Extended sway bar links. Solid alloy bodies with heim ends, so they articulate through the full range of travel. The factory pins and bushes bind well before the suspension runs out of travel, and that bind is costing you both articulation and bar effectiveness.


Bump stop extensions. Control up-travel so the tyre stops before it finds the guard or chassis. Protects the arms, panhard and bodywork when you are actually using the travel this kit provides.


The result

Predictable, progressive body control on and off road instead of the sudden lean and unload you get standard. Torque induced lean under throttle largely gone. A rear end that stays loaded through a corner and keeps biting for traction. Roll and flex steer reduced to the point you stop noticing it. Longer bush and joint life, which pays for itself over time. Room to run larger tyres without scrubbing the guards. And the main fuel tank stays exactly where it is.


Kit includes

  • Long arm kit: 290mm longer lower links, new lower chassis mounts, dropped upper link chassis brackets
  • Solid alloy upper links with bush/heim combination
  • Extended sway bar links, solid alloy with heim ends
  • Panhard riser bracket
  • Extended panhard bar
  • Bump stop extensions


Why not a 4-link?

A 4-link is the ceiling for rear end performance and we'll build you one. It also costs you the main fuel tank and a serious fabrication job. If you want the best result achievable while keeping the factory 5-link and everything that comes with it, this kit is it.


Installation

The long arm chassis brackets are the only components in this kit that require welding. Everything else bolts in.


Rod ends

We run DFI and FK rod ends throughout. DFI are a quality unit and do the job properly. FK are widely regarded as the best available, and the price reflects it.


Every component in this kit is available individually, so it can be built up over time if that suits the budget better.

Complete the setup