{"product_id":"gu-patrol-double-shear-race-kit","title":"GU Patrol - Double Shear Race Kit","description":"\u003cp\u003eAre you racing or building a Patrol for competition? A known weak point under extreme stress is the tie rod ends. Well, we have the solution for you!\u003c\/p\u003e\u003cp\u003eWe have designed this GU Double Shear kit to make your steering far stronger \u0026amp; more reliable.\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003eRunning heim joints in steering arms is extremely common for race cars.\u003c\/p\u003e\u003cp\u003eWith large amounts of vertical diff movement \u0026amp; abuse, most TREs either wear out prematurely, or even break under the high stress working conditions.\u003c\/p\u003e\u003cp\u003eHeims are a great alternative, but with the drag link seeing so much lateral force, you're asking a lot from a single shear 16mm bolt. Not to mention simply drilling the coupling out will leave approximately 1\/4 of the hole larger than the bolt size you'll be running. This oversize will cause the bolt to constantly come loose, or worse, break!\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e\u003cu\u003e***PLEASE NOTE***\u003c\/u\u003e\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e- This kit requires a moderate skill level, in both fabrication and welding, to install. Both the knuckle and pitman arm are cast, which will require pre and post heat for install to prevent potential failure. \u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e- This kit is NOT a high steer kit for hydro steering. (Bracket for passenger side swivel housing and pitman arm only.)\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e- Not suitable for road registered vehicles. WILL NOT pass an engineering certificate. Off-road and race car purposes only!\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e- The height of the drag link on the knuckle can be modified by changing the length of the crush tube to suit your application. \u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCNC Cut 10\/6mm Mild Steel\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e\u003cu\u003eFULL KIT INCLUDES:\u003c\/u\u003e\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003ex 3 Knuckle plates\u003c\/p\u003e\u003cp\u003ex 2 Knuckle gussets\u003c\/p\u003e\u003cp\u003ex 1 Pitman plate\u003c\/p\u003e\u003cp\u003ex 1 Pitman gusset\u003c\/p\u003e\u003cp\u003ex 2 Weld washers\u003c\/p\u003e\u003cp\u003ex 2 Crush tubes\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003eAll required hardware\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e\u003cu\u003ePITMAN ONLY KIT:\u003c\/u\u003e\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003ex 1 Pitman plate\u003c\/p\u003e\u003cp\u003ex 1 Pitman Gusset\u003c\/p\u003e\u003cp\u003ex 1 Weld washer\u003c\/p\u003e\u003cp\u003ex 1 Replacement bolt\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e\u003cu\u003eINSTALLATION:\u003c\/u\u003e\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003e- Be sure to thoroughly clean \u0026amp; degrease the knuckle before assembly. This also avoids smoke while heating.\u003c\/p\u003e\u003cp\u003e- The knuckle will require a slight grind (the white coloured section pictured) for the plate to sit flat on the kingpin mating surface.\u003c\/p\u003e\u003cp\u003e- Before any preheating or welding, test fit the entire assembly as pictured. Clearance if required. Knuckle \u0026amp; pitman arm need to be drilled to 16mm.\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e**We recommend using spacers in place of heims etc. to retain spacing while welding. \u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003e- While still bolted together, tack weld the pitman arm plates, the small tapped plate \u0026amp; gussets in position. The upper 2 plates can be tacked together at this stage. (Not to the knuckle)\u003c\/p\u003e\u003cp\u003e- Tack weld crush tube \u003cstrong\u003e\u003cu\u003eA\u003c\/u\u003e\u003c\/strong\u003e into position, with a heim or spacer to set height. \u003c\/p\u003e\u003cp\u003e- Preheat the entire assembly thoroughly (a BBQ or oven works wonders here)\u003c\/p\u003e\u003cp\u003e- Fully weld the small plates \u0026amp; gussets to the knuckle, inside \u0026amp; out. Same with the pitman arm.\u003c\/p\u003e\u003cp\u003e- Fully weld the top 2 arms to each other as shown (not to the knuckle)\u003c\/p\u003e\u003cp\u003e- Finally, weld crush tube \u003cstrong\u003e\u003cu\u003eB\u003c\/u\u003e\u003c\/strong\u003e aligned with the top brake caliper bolt as shown\u003c\/p\u003e\u003cp\u003e- Place back into the BBQ or oven, slowly turning the heat down over approximately an hour or so. Wrap the entire assembly in a welding blanket or similar \u0026amp; allow to cool as slowly as possible.\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e\u003cu\u003eDisclaimer\u003c\/u\u003e\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThese steering arms are designed for off-road, competition and race vehicles \u003cstrong\u003eONLY\u003c\/strong\u003e. Rampt takes no responsibility for the misuse or misinterpretation of the designed use of this product.\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e","brand":"Rampt Customs","offers":[{"title":"FULL KIT","offer_id":50657400062144,"sku":null,"price":580.0,"currency_code":"AUD","in_stock":true},{"title":"PITMAN END ONLY","offer_id":50657400094912,"sku":null,"price":75.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0791\/0611\/3728\/files\/SYL6IL3VCE4VRU3F4KIMZOII.jpg?v=1793453815","url":"https:\/\/ramptcustoms.com.au\/products\/gu-patrol-double-shear-race-kit","provider":"Rampt Customs","version":"1.0","type":"link"}